How To Repair Leaking Stem On Freeze Proof Outside Faucet

Frost-Proof Sillcock Installation& Leak Repair
Install, diagnose & prepare leaky frostproof sillcock anti-siphon valve

• Postal service a QUESTION or Annotate most outdoor wall faucets, sillcocks, hose bibbs, and freezeproof or frostproof faucets or faucet troubleshooting

InspectAPedia tolerates no conflicts of interest. Nosotros have no relationship with advertisers, products, or services discussed at this website.

Diagnose & fix frostproof hose bibb & sillcock leaks:

This article series gives the steps in diagnosing leaks at outdoor spigots, hose bibbs, or sillcocks.

As our illustration at folio tiptop explains, the long shaft (greenish) of this frost-proof faucet permits the actual stem washer and valve seat to be located on the warm side of the building outside wall.

Using the popular Woodford Model 17, we illustrate & explicate the steps in replacing a leaky sillcock anti-siphon valve.

This article serial describes outdoor faucets, hose bibbs, sillcocks, or hose hookups, how they work, where they should be installed, freeze-proofing hose hookups, and troubleshooting or repairing stuck, broken, or dripping outdoor faucets.

We too provide an Article INDEX for this topic, or you tin effort the page pinnacle or lesser SEARCH BOX equally a quick manner to find information you demand.

How to Install or Repair a Leaky Frost-proof Outdoor Faucet SillCock or Hose Bibb

Frost-proof or freeze-proof outdoor hose bibbs or sillcocks use longer-stem frost-proof outdoor faucet (shown at left). These are required in new construction in most jurisdictions. This outdoor includes a vacuum breaker is designed to permit water to drain out of the faucet when the faucet is closed.

Explanation of the faucet's anti-siphon feature: The vent (allowing air into the faucet) combines with a bank check valve to prevent back-flow of unsanitary water from a garden hose backwards into the edifice water supply pipage.

Explanation of the faucet'due south frost-proof characteristic: The long faucet body of a frost-proof hose bibb is long enough to extend fully through the building exterior wall or foundation and into indoor or heated space, places the actual shut-off stem washer and valve-seat within the edifice.

[Click to enlarge any prototype]

Frost-proof outdoor faucets are installed with the faucet trunk sloping down from its connection inside the building.

This position assures that when the faucet is turned off, any h2o remaining inside the faucet trunk will drain fully.

As we explained to a higher place in describing standard compression type hose bibbs, you should never leave a garden hose attached to the outdoor faucet in winter.

Even with a frost-proof faucet, water in the hose may add to the risk that the faucet will be freeze damaged by preventing the faucet from draining fully even when it is turned to the "off" position..

The sketch above, showing the two types of outdoor water faucets is provided courtesy of Carson Dunlop Associates, a Toronto home inspection, didactics, and report-writing company.

What Kind of Faucet Have I Got?

Before starting to tear things apart or to buy repair parts, let'southward check that we know what kind of faucet we're repairing: the procedures and parts are non the same.

Our starting time photograph above is a typical frost-complimentary anti-siphon faucet, or "Woodford" valve. Repairing that faucet is discussed here on this folio.

If your outdoor faucet looks similar our 2nd photo at to a higher place, and if needs repair, it is Not a frost-proof anti-siphon valve, information technology's a traditional pinch valve faucet or spigot. Y'all want to meet the leak repairs starting

at FAUCETS, OUTDOOR HOSE BIBBS

Why do we Want an Anti-Siphon Faucet?

How might nosotros get backflow from a garden hose into the building piping? Piece of cake. Suppose yous are filling an higher up-basis pool, or a fish pond, with your garden hose.

The above-ground pond in our photograph at left includes three levels, at least two of which are high enough to cause water dorsum-flow when the swimming fill-hose is left connected as shown in our photograph.

As long as the upper surface of h2o in such an outdoor water container is higher than the hose bibb location on the building, the potential for dorsum-flow occurs.

Back-flow of h2o from such a source through an open hose bibb faucet would and then occur if the building happened to lose water pressure.

Besides see CROSS CONNECTIONS, PLUMBING.

How to Repair Sillcock Leaks at the Anti-Siphon Valve

This leaky anti-siphon hose bibb is the same one as shown earlier in this article, earlier information technology leaked. The hose bibb worked perfectly for almost fifteen years before in a sudden change of behaviour information technology began gushing water when the faucet was opened.

Question: where can I get repair parts for my frost-free anti-siphon sillcock

2018/06/27 Jim said:

I would similar to supercede the only the stalk associates (iv inch, spring loaded) in my frost gratis anti-siphon sillcock. Where the handle attaches the stem associates is very bent.

As well, to supervene upon the whole sillcock would require I open up a hole in the bedroom wall.

I'm having trouble finding the replacement role and would like to know if anyone can identify the attached stem assembly and know where I could find one. Thanks

Reply:

Jim

Have the valve stalk that yous removed to a good hardware store and you may find they accept a plethora of Replacements one of which volition match.

Or if you lot tin see a brand and model on the sillcock, such every bit the Woodford No. 17 shown in a higher place on this folio, yous can buy the verbal parts from your local plumber supplier or you can guild replacement parts from online vendors.

I agree that for a typical frost-proof sillcock installed in a edifice wall above ground you lot volition accept no access without cut an access opening in the wall from inside or outside.

The Woodford sillcock shown above is installed in a wall outside of a bathroom on a wall abutted within by a bandage iron bath tub. In that location is no access from inside the building whatsoever. (Y'all'd accept to demolish the bathroom to remove the bathtub.

A plumber having to replace the entire sill-cock would cut an admission opening from outside, make the repair, and so repair the wall.

Reader follow-up:

Found the frost gratuitous anti-siphon hose bib at a local plumbing supply store

It just cost nigh $twenty. I will rob the stem assembly from the new hose bib and insert it into the old (all the same proficient) hose bib. Will save time and money from cutting a hole in my wall to get to the pipe connectedness and replace the whole thing.

Answer: How to Replace the Anti Siphon Valve on a Frost Gratis Woodford No. 17 hose bibb

Very smart, Jim.

But before replacing the valve stem, let'southward be sure we sympathise just where the leak is occurring.

[Click to enlarge any image]

You can identify the brand and model of your frost-gratuitous anti-siphon faucet by looking at the cap - photograph below.

Mansfield sillcocks series #500 use a grey plastic cap on the anti-siphon valve.

Woodford sillcocks use tan colored plastic and the anti-siphon valve cap is marked WOODFORD MODEL 17 ANTI SIPHON.

Find the Exact Sillcock Leak Before Trying to Repair It

Now look very closely at where h2o is leaking out of the valve.

In our photo higher up water is gushing out of this sillcock valve, but we need to await more than-closely to see exactly where the leak is originating. In my photograph the yellow arrows point to the gush of water.

The bluish arrow points to the most-mutual leak bespeak at a hose bibb: leaks at the hose connection to the faucet mouth. Remove the hose and replace the hose washer and re-tighten information technology.

The greenish arrows point to occasional leaks at the valve stem or its packing washer.

The cherry arrow points to the point at which h2o will leak if the hose bibb or sillcock'due south anti-siphon valve has failed.

Hither are 3 dissimilar cases:

1. If water leaks from the valve outlet when the faucet handle is closed, (blue arrow) then the valve stem washer, or (rarely) the valve stalk itself may need replacement.
2. If water leaks around the valve handle stem (green arrows ) and so the valve packing or packing washer is leaking and might need to be replaced, though on occasion a slight gentle tightening of the packing nut will stop such a leak.
3. If water leaks from the plastic cap covering the anti-siphon valve when the valve is open up (cherry-red pointer and also the photo below) then the anti-siphon valve associates (simple plastic parts) should be replaced.

If the leak is at the chocolate-brown (or gray on some brands) plastic cap on top of the anti-siphon hose bibb like the Woodford No. 17, those parts can be replaced quite easily without replacing the entire valve and without removing the valve stem at all.

Does your frost-free anti siphon valve wait similar the Woodford model No. 17 I show here?

Other frost-proof sillcocks such as Mansfield have similar features and tin be repaired past ordering the proper repair kit for your valve brand and model.

Watch out: repair parts are generally not interchangeable between sillcock brands.

A Mansfield repair kit sold by Danco for the Mansfield-brand Series #500 sillcocks volition not, for example, repair a Woodford-brand Model #17 sillcock.

Even though the white plastic anti siphon cap threads will fit into some other brands of sillcocks (such as Woodford) the Mansfield#500 anti siphon valve will Not work in the Woodford Model #17 - we tried it and establish that it simply leaked like mad.

Woodford sells sillcock faucet repair kits for all of their product line through plumbing suppliers, building supply stores, too equally online vendors and by their ain website given at the terminate of this commodity.

All of these parts can be replaced on the Woodford hose bibb working from outside.

However if the leak problem is only at the anti-siphon valve a simpler and less plush repair will be sufficient: remove the plastic cap, un-spiral the anti-siphon valve, and replace the 2 parts (the threaded fitting and the washer-bearing pressure-operated valve seal inside) with the parts from the repair kit. And so snap the new plastic comprehend cap in identify.

How to Supercede the Anti Siphon Valve on a Woodford Model 17 Hose Bibb

Above are the three parts you'll demand.

At your local plumbing or hardware store as well as from online vendors or building suppliers you lot can buy a replacement kit that includes just these items.

Pace 1: remove the plastic anti siphon valve cap

Stride two: un-screw the anti-siphon valve

My photo above shows what happens if y'all turn h2o on at this signal: that's considering the anti-siphon valve or its washer is dislocated or the valve is damaged.

I've successfully disassembled, cleaned-up and re-assembled old anti-siphon valve parts to repair a leak like this but a better approach is to simply replace the parts. That's a more than-reliable repair.

My photo just above shows loosening the plastic anti-siphon valve assembly.

Once loosened, you can un-spiral this plastic part by hand.

Below I'm property the old anti-siphon valve parts (starting time photo) and the replacement parts (2d photo).

The replacement anti-siphon valve parts await different merely they work just fine in older Woodford Model 17 sillcocks.

Footstep 3: insert the new anti-siphon valve parts in the proper position

Starting time put the smaller valve component into the underside of the clear plastic cap then that the washer is up within the cap, non downward towards the faucet body.

Turn this assembly over so that you lot tin can thread it carefully into the brass torso of the sillcock.

In my photograph I'1000 holding the assembled valve with its upper side "up" - you can meet through the clear plastic that the plastic pin on the red washer-bearing plunger is through the small pigsty in the heart of the clear cap.

Take intendance not to cross thread the anti-siphon valve plastic role.

If the small-scale center plunger falls down into the valve, utilise a tiny screwdriver or equivalent to center information technology in the valve caput infinite so that when you spiral downward the threaded valve peak the plunger moves into the hole in the center of the peak.

Step 4: Tighten the replacement anti siphon valve

Tighten the assembly by manus then gently snug it downward with your gooseneck pliers. Don't over-tighten the valve and take care not to damage these plastic parts.

Footstep 5: Supervene upon the anti siphon valve plastic cap

Lookout out: before replacing the cap, turn on the hose bibb - open the faucet handle - and verify that the sillcock'south anti-siphon valve is not leaking.

You'll see water enter the clear plastic valve top and you may notice the ruddy washered plunger snap up against the nether-side of the valve top.

Water should not exist leaking out of the anti-siphon valve at this point though of form, water is pouring all over your feet as you've opened the sillcock.

In my photo above [Click to enlarge whatever image] yous may see that there's h2o inside of the valve, considering I've opened the sillcock for testing.

Below, I've replaced the original cap - it just snaps in place.

You can use the new plastic cap. But I re-installed the old plastic cap for a trial run as it'south obvious that you tin can't remove the plastic cap over again without chewing it up with your pliers.

I kept the new un-damaged cap in reserve, planning to install information technology to replace the ugly chewed-upwards original cap once I'm certain that the repair was successful.

Step 6: Mistake to Avoid: A Closed Hose Manifold will Accident the Anti-Siphon Valve on a Sillcock

Watch out: especially if h2o pressure is high at your building, if you install and close any blazon of shutoff valve downstream from the sillcock'south outlet and then open the sillcock valve the h2o pressure may blow out the anti-siphon valve.

To avoid that fiasco, BEFORE OPENING THE SILLCOCK be certain that AT LEAST Ane DOWNSTREAM VALVE is Open.

Watch out: extract from instructions for installation of the Legend Valve sillcock cited simply below:

Avert the apply of hose bibb accessories such as hose manifolds, hose Y-splitters or sprinkler timers, which may cause the TM-550 to malfunction. . The TM-550 is designed and certified in accordance with ASSE Standard 1019 Department i.2.one, for non-continuous pressure service: Non more than than twelve hours of continuous water pressure. Outlet-mounted devices may cause sudden or continuous, damaging.

Replacing the Entire Frost-Proof Anti-Siphon Sillcock Valve

Lookout man out: while you cannot simply pull out a sillcock that was soldered in place, valves are sold terminating in either a solder-type or sweat plumbing fixtures OR in a threaded plumbing fixtures.

IF you knew that your valve is at threaded fitting installation, it might be possible to unscrew an existing sillcock like the Woodford valve shown below from exterior the building.

You would remove the screws in the plastic mounting flange and then attempt to remove it, wrap the replacement sillcock valve threads with teflon tape and screw the new 1 back in place.

But in that location are some serious risks with this "easy" sillcock replacement approach:

1. Flooded wall cavity: If you lot were not able to completely shut off water supplying the sillcock when you remove it you will overflowing the wall cavity, wet the insulation, and run a risk a serious h2o damage or mold contagion trouble.
2. Wet wall cavity: Even if you were successful in shutting off the water supplying the sillcock when you remove it some h2o is likely to spill out of the valve as well every bit the supply pipage into the wall crenel: aforementioned hazards as above, though smaller in scope.
3. Continued leaks into the wall crenel: because you cannot see the plumbing connection betwixt the sillcock and the receiving plumbing plumbing fixtures in the wall cavity, there is a risk that your connection leaks continuously, ultimately causing the same sort of damages as in warnings #1 or #2 above.

To avoid these risks, if you cannot repair the hose bibb / sillcock by installing a repair kit or a new valve stem and repair kit while leaving the valve torso in place, I'd cut an access opening in the outside wall or in the interior drywall if that location is accessible, and I'd audit for leaks earlier, during, and after the repair.

Where to Buy Frost-Proof Anti Siphon Valve Hose Bibbs, Sillcocks, & Grand Hydrants

What'south the difference betwixt a regular sillcock, a frost-free sillcock, and a one thousand hydrant?

Sillcock: Here we illustrate first a conventional sillcock or hose bibb intended to exist mounted on the exterior wall of a building, supplied past building cold h2o (usually) piping. This is Non a frost-proof sillcock and this valve does Not include an anti-siphon feature.

This sillcock valve is intended for use in climates where freezing is not a concern.

[Click to overstate any image]

In a freezing climate where hose bibbs like this one are installed, the plumber should take installed a shut-off valve within the heated building interior.

Before freezing atmospheric condition arrives the indoor shutoff valve is closed and then the sillcock or hose-bibb is opened to drain.

Watch out: be sure you shut off the water supply to this valve indoors earlier freezing weather. Otherwise the valve and piping nearly information technology can freeze, flare-up, and may leak into the building, causing costly harm.

Watch out: when you turn off the in-edifice h2o supply to this type of hose bibb or sill cock, call back to go back outside and open the valve so that information technology volition drain completely - to avoid possible frost damage to the valve.

When you open up the valve to drain information technology bank check to be sure that water stops dripping in a few minutes. If water continues to run or drip then the indoor shut-off valve is not fully airtight, or is leaky and needs repair.

Frost-Proof Sillcocks similar the valve shown to a higher place (from a Home Depot store) are designed to bleed out when turned off. The same features that improve drainage out of the valvce when it's airtight provide an anti-siphon characteristic that prevents back-siphonage of hose water (or nasty water into which the cease of the hose rests) back into the edifice water supply where it might contaminate building pipage.

The photo shows the long valve body that assures that the bodily shutoff is inside the heated infinite.

Sillcocks discussed in the article above, as well called "hose bibbs" are used to provide an outdoor water or hose hook-upward at a building wall.

The water supply pipage to the sillcock is routed through the building, in common cold climates through a heated space, then must pass through the building wall to the exterior where a hose connexion is provided.

Sillcocks may not be lead-free - including those listed beneath.

Frost Proof M Hydrants: a yard hydrant is usually a gratis-continuing outdoor water supply spigot used for watering or for livestock.

It is fed by underground h2o piping. Every bit y'all'll note from our analogy below, adapted from Menards' yard hydrant installation instructions cited farther below, to exist frost-proof or freeze-damage-proof, in that location are several features required:

• The hydrant's valve should be below the frost line - the deepest point in the soil that is expected to freeze during cold weather
• The water supply pipe to the hydrant should be below the frost line
• A gravel bed is provided around the yard hydrant's buried valve. This gravel allows the hydrant'due south vertical standpipe to drain out when the hydrant valve is closed.
• Typically h2o pressure level to the hydrant is at lxxx psi or less and recommended operating pressure level is 20-40 psi.
• Support (a concrete block or large stone) is placed under the elbow at the lesser of the hydrant to prevent settlement of the hydrant assembly in loose soil caused by hydrant drainage.
• Watch out: if the hydrant is to exist installed below a paved area or inside of a befouled or outbuilding, a drain pipe and drywell or equivalent must be provided into which the hydrant can drain when it'south turned off. Otherwise hydrant drainage may upshot in a muddy area within the building or a wet expanse in or frost impairment to the pavement.

  Watch out: most plumbing codes volition require a vacuum breaker on the thousand hydrant's water supply piping to forestall potential back-contamination of the building h2o supply piping and water itself.

Lookout out: some sillcocks and yard hydrants, even including anti-siphon brawl valves and sillcock models contain lead and practice non comply with the U.South. Safe Drinking H2o Deed.

Those valves should Non be be used anywhere that h2o passing through them volition be consumed past humans nor (in our OPINION) other animals including livestock and for fish ponds.

Watch out: Never go out a hose attached to the hydrant after use. This volition forestall the hydrant from draining properly and volition cause the hydrant to freeze in cold atmospheric condition. Leaving the hose fastened could also siphon contaminants back into the water system. - this quote appears in literature from Everbilt and from Watersource.

Where to Buy & Installation Instructions for Sill-cocks & Hydrants

In that location is a nearly-overwhelming number of sillcock brands that specifically annunciate that they are pb free, including some of the following.

• American Valve FREEZE-PROOF SILLCOCK INSTALLATION INSTRUCTIONS [PDF], Model M73AS, American Valve, retrieved 2022/08/13 original source: https://world wide web.americanvalve.com/perch/resource/pages-from-avm73as-installationv102-nineteen-003.pdf
• ARROWHEAD FROST-PROOF WALL HYDRANT INSTALLATION, USE, REPAIR GUIDE [PDF], Arrowhead 456-06LF 1/two" frost free hydrant, length for 3 three/4" wall thickness (shown above) retrieved 2022/08/13, original source: http://champion-arrowhead.com/media/wysiwyg/PDFs/Frost-Free_Hydrant_Guide.pdf

  Arrowhead frost-proof hydrants (sillcocks) are sold in lengths suitable for diverse wall thicknesses: 4", half-dozen", viii", 10", 12" and 14" walls . This document also includes details on how to de-code the frost-proof sillcock model number to be sure that you're buying the correct device for your wall thickness AND the inlet piping blazon (such as push-fit, PEX, Crip Pex, threaded copper, sweat copper, etc.

• B&M Industries 104-117 x-inch Frost Free Sillcocks (sold at plumbing suppliers and online at Amazon)
• BMI Canada, BMI FROST PROOF FAUCET INSTALLATION INSTRUCTIONS [PDF] BMI, 3437, Grande Allee Blvd, Boisbriand, Quebec J7H 1H5 Canada, Tel: one-800-361-1452, also offices in Mississsauga ON, retrieved 2022/08/13, original source: http://www.bmicanada.com/products/bmi_specs_frost_free_installation.pdf
• Boshart Industries, Boshart 0865(P)-Series self-draining vacuum breaker ("anti-siphon) Spec Sheet [PDF]
  Boshart Industries, 25Whaley Ave., Milverton Ontario Canada N0K 1M0 Tel: 800-561-3164 Website: www.boshart.com
• Greenbacks Top #24636 Frostproof sillcock, ane/two" x 12" long.
• Everbilt Frost-Proof Thou Hydrant INSTALLATION & ADJUSTMENT INSTRUCTIONS [PDF], sold at Dwelling Depot stores, retrieved 2022/08/13, original source: https://images.homedepot-static.com/itemize/pdfImages/f5/f5f0c554-952d-4a4a-8649-3b85788d9f58.pdf

  Excerpt: Watch out: Never leave a hose fastened to the hydrant after use. This will prevent the hydrant from draining properly and will cause the hydrant to freeze in cold conditions. Leaving the hose fastened could too siphon contaminants dorsum into the water system. - this quote appears in literature likewise from Watersource.

• Jomar Valve, Jomar T540-G (lead-free dezincification-resistant brass) [PDF] Jomar Valve, 7243 Miller Dr. Warren, MI 48092 U.s.a. Tel: ane-800-325-5690 Spider web: www.jomar.com

• Fable Valve, MODEL TM-550 MULTI-Plough ANTI-SIPHON FROST-Free SILLCOCK INSTALLATION INSTRUCTIONS [PDF] Fable Valves, 300 North. Opdyke Rd. Auburn Hills, MI 48326 USA Tel: (800) 752-2082 Website: world wide web.legendvalve.com retrieved 2022/08/xiii, original source: http://world wide web.legendvalve.com/images/technical/IOM_TM-550_multi-turn_FFSC.pdf
• Mansfield Sillcocks, 4515 East 139th Street Grandview, MO 64030 USA, Website: world wide web.prier.com, Tel: 800-362-9055 Prier purchased Mansfield'south Brass Partitioning in 2007

  Annotation: Mansfield's 500-series Anti-Siphon wall hydrant is a retired production. Parts for the current Prier 400-series sillcock are Non interchangeable with the older 500-series.

  Nevertheless both Prier and a carve up visitor, Danco Inc., Irving TX USA 75062 sell (made in Communist china) repair kits for that sillcock.

• Matco-Norca Valves, Matco 212 Frost Freer Sillcock, Anti Siphon Spec-Sheet [PDF] , 1944 Route 22 PO Box 27 Brewster, New York 10509 Toll-Gratuitous: 800-68-VALVE (688-2583) New York Toll-Gratuitous: 800-431-2082 Texas Cost-Free: 800-935-5456 Illinois Toll-Free: 844-412-5068 California Cost-Gratis: 866-532-8306 Website: https://www.matco-norca.com

• Menards YARD HYDRANT INSTALLATION GUIDE [PDF] retrieved 2022/08/thirteen,
• Merrill Manufacturing, MERRILL C-1000 YARD HYDRANT INSTALLATION INSTRUCTIONS [PDF], retrieved 2022/08/13 fdrom suppliesdepot . com original source https://www.merrillmfg.com/production/installation-instructions-c-k-serial-yard-hydrant
• Mueller 104-405 ProLine FrostFree Sillcock Valves (shown above) - sold at hardware stores, plumbing suppliers, building suppliers; at that place are at least xix models of Mueller anti-siphon frost-free sillcocks or frost-gratis hydrants or hose bibbs with varying lengths, materials, dimensions.
• Prier Heavy Pattern Angle Sill Faucets, MANSFIELD STYLE 300-DIAMOND SERIES WALL HYDRANT INSTALLATION INSTRUCTIONS [PDF] Prier, 4515 E 139th Street Grandview, MO 64030 (800) 362-9055 Fax (800) 362-1463 Website: www.PRIER.com

  Prier produces both "Freezeless" wall hydrants such as their 300/400/500 -serial Freezeless hydrants (and more models such as the C-134/234 Series Freezeless wall hydrant) , and sill faucets that are not frost-protected.

  Excerpt:

  PRIER Heavy Blueprint Bending Sill Faucets are designed for areas that require water service, but are not subject to freezing temperatures. Typical installations include basements, garages and for outdoor installations in mild climates. The heavy blueprint design with solid brass stalk assures years of reliable service with minimal maintenance.

• Proline frost-complimentary sillcocks, widely sold at plumbing suppliers and online
• Raven Products, #FP-1132-series w/ ceramic cartridge sillcocks, frostproof Website: www.ravenproducts.united states - sells only to wholesalers
• SharkBite Frost Free Sillcocks, available from
  SharkBite Plumbing Solutions, SharkBite USA 2300 Defoor Hills Rd. NW Atlanta, GA 30318 United states of america Tel: ane-877-700-4242

  SharkBite Canada 74 Alex Avenue Vaughan, Ontario, L4L 5X1 Canada, tel: 1-888-820-0120 retrieved 2022/01/19 original source: https://www.sharkbite.com/

  SHARKBITE INSTALLATION GUIDE [PDF] (2018) Reliance Worldwide Corporation 2300 Defoor Hills Rd NW, Atlanta, GA 30318 Phone: 1-877-700-4242 Fax: one-877-700-4280 rwc.com Reliance Worldwide Corporation (Canada) Inc. 74 Alex Avenue Vaughan, Ontario, L4L 5X1 Phone: i-888-820-0120 Sales Inquiries: canadasales@rwc.com Orders: canadaorders@rwc.com retrieved 2022/08/13 original source: https://www.sharkbite.com/sites/chiliad/files/rgohfh321/files/2018-05/SharkBite_Installation_Instructions_2018_WEB.pdf

• Simmons FROST PROOF YTARD HYDRANT REPAIR INSTRUCTIONS [PDF], Simmons Manufacturing P.O. Box 1509 McDonough, GA. 30253 1608 Highway 20 East McDonough, GA. 30252 USA Tel: (800) 241-1935, retrieved 2022/08/13 original source: http://world wide web.simmonsmfg.com/wp-content/uploads/2012/11/HydrRepairInstr.pdf
• Sioux Principal Sioux-Chief FROST PROOF SILLCOCK ANTI SIPHON OPERATING INSTRUCTIONS [PDF] Sioux Primary, P.O. Box 397 24110 S Peculiar Drive Peculiar, Missouri 64078 U.South.A Tel: i-800-821-3944 Email: info@siouxchief.com Website: https://www.siouxchief.com retrieved 2022/08/13 original source: https://www.siouxchief.com/docs/default-source/technical-documents/installations/supply/frost-proof-anti-siphon-sillcock---instruction-sheet
• YARD HYDRANT INSTALLATION INSTRUCTIONS [PDF], Fairfield Department of Health, retrieved 2022/08/13 original source: https://www.myfdh.org/pdf/Yard-Hydrant-Installation.pdf
• Watersource, WATERSOURCE YARD HYDRANT INSTALLATION [PDF], Watersource, P.O. Box 3795 Mansfield, Ohio 44907 USA, Tel: 800.346.7611 Website: www.watersourceusa.com retrieved 2022/08/13 from northerntool.com
• Watts Corporation, Serial FHB-1, FHB-2 ANTI-SIPHON FROST-PROOF SILLCOCK INSTALLATION [PDF] Watts USA: T: (978) 689-6066 Watts.com Canada: T: (905) 332-4090 Watts.ca Latin America: T: (52) 81-1001-8600 Watts.com

  Watts besides sells a lead-free series LF8 hose connectedness vacuum breaker that is an addition vacuum breaker between an existing hose bibb and a garden hose.

  Excerpts from product description:
  Serial LF8 is a line of unique vacuum breakers especially fabricated to permit the attachment of portable hoses to hose thread faucets.

  Designed to prevent the flow of contaminated h2o back into the potable water supply, these devices require no plumbing changes and screw directly onto sill cocks. The Serial LF8 features Lead Free* structure to comply with Pb Free* installation requirements.

  Series LF8 can be used on a wide diverseness of installations, such as service sinks, swimming pools, photograph developing tanks, laundry tubs, wash racks, dairy barns, marinas and general outside gardening uses.

  - source: http://media.wattswater.com/ES-LF8.pdf 2022/07/17

• Webstone Valves (a NIBCO) brand, HOW TO SWT A BALL VALVE Installation Instructions [PDF] Webstone, a brand of NIBCO 60A Solferino Street Worcester, MA 01604 United states Tel: (800) 225-9529 retrieved 2022/08/13 original source: http://world wide web.webstonevalves.com/customer/wecoin/PDF/swt_instructions.pdf
• Woodford ANTI-Outburst FREEZELESS WALL FAUCET INSTALLATION INSTRUCTIONS [PDF], Models 16 (without anti-siphon) & xix (with anti-siphon protection), Woodford Manufacturing Company, 2121 Waynoka Rd., Colorado Springs CO 80915 U.s., Website: www.woodfordmfg.com, Tel: 800-621-6032, email: sales@woodfordmfg.com
  Woodford is a division of WCM Industries, Inc. retrieved 2022/08/thirteen original source https://world wide web.woodfordmfg.com/woodford/Installation/16-nineteen%20Installation%20Instructions.pdf
• other manufacturers, varying by state.

Reader Comments & Q&A

Jim

Cheers so much for the helpful post and photograph.

I take also come across the "incorrect threads" problem on other plumbing repairs, such every bit in trying to connect upwardly or find fittings to marry flare fittings, pinch fittings, and normal or standard US "NPT" thread pipage fittings. For example some flare fittings are sold in both a coarse thread and fine thread version.

I use several like shooting fish in a barrel "tricks" to check thread compatability, similar to your ain experience:

ane. find a fitting or function that screws properly onto the "old" role and use that matching plumbing equipment (cap, nipple, etc) to select and purchase the proper replacement part

ii. Use a thread estimate (shown below)

3. Make note of devices using special threads or fifty-fifty reverse threads (uncommon but does occur)

@Tony Paccione, I had that "plough forever" problem for a sillcock valve with a new stem I just bought. Finally, by comparison the old-vs-new stem, I immediately saw the reason: the stems were alike EXCEPT for the thread pitch.

The advice from danjoefriedman is of import -- in addition to checking the thread condition, realize that the "same" stem isn't really the same unless it'southward the same make proper name; no standardization.

Tony,

Practise you lot still have the old parts?

If so, lets compare old and new hydrant stem lengths

Also, shine a light into the receiving end and check thread condition.

I have rebuilt my Mansfield 500 series hydrant stem with the items in the repair kit. This is the first time this has been done, the house was built in 1992. Now that it is rebuilt, the threaded end of the stem (inside the firm) will not "catch". I cannot screw this stalk in. What could exist the trouble? The new handle is assembled merely it continually turns both left and right. Delight aid/advise. Thanks
Tony Paccione
Brick, NJ 08723
avp0713@comcast.net

Quite possibly, Greg, moreso depending on who actually made the hose bibbs.

Am I right that but tightening the packing nut around the valve stalk doesn't fix the trouble?

I've installed brand new model 17 bibbs at iii unlike addresses over the past four years. Each has persistent leaking at the valve stalk when the faucet is 'on". This occurs whether the faucet is 'fully 'on' or 'partially 'on'. This is VERY frustrating, being that the faucets are brand new. Is this a blueprint flaw?

Since the entire plastic function needs to be removed anyway I don't feel bad about gouging information technology upward in order to create a slotted which I can insert a screwdriver or other tool to effort turning it. Sometimes you can also tap the plastic advisedly with a small screwdriver to cause it to turn in a counterclockwise Direction

Woodford RK-17 anti-siphon valve was leaking. I removed the cap and tried to loosen the clear plastic trunk of the anti-siphon piece. The pinnacle of the valve broke off and I tin can't remove the threaded office of the valve. Any ideas how to loosen it?

Dave

If y'all're in a freezing climate it makes sense to install a frost-proof hose bib. Details are at SILLCOCK INSTALLATION & REPAIR

Most probable - varying by the country and city where you live - you need a edifice or plumbing permit and at least 2 inspections, a crude-in inspection and a final inspection.

Mounting a sillcock (hose bib) through OSB covered with vinyl siding and connecting to PEX (why are you running ruddy (hot h2o) PEX to an outdoor sillcock?) yous may demand blocking inside the wall between studs to be sure your sillcock is securely mounted.

This illustration is from the sillcock installation instructions for a Legend Model TM-550 Multi-Turn Anti-Siphon
Frost-Free Sillcock Installation Instructions - details are at the article I already cited

I am plumbing by myself, an addition to my home. In the addition, the plumbing will consist of; 1) a clothes washer connectedness, and drain. 2) a utility tub connection and drain. 3) A hose bib connection for exterior apply.

Once I accept all the h2o and bleed lines in identify, practice I have to charge the water lines with water, to pass the building lawmaking inspection or just take them run to where they will go, and I don't even have to have them connected to faucets etc? Will the inspector want to look at my 'bodily',/ physical, water connections, ( to the utility tub faucet and clothes washer h2o connections and the out door faucet) Thanks for this opportunity to ask my questions, and I look forward to reading your reply.

I want to install a outside water hose bib on a one/2 inch thick OSB wall that has vinyl siding on the exterior. The wall studs are 2x4s. Do I want a freeze proof hose bib, and if and so, what blazon, and size to purchase? Somewhen, This plumbing will have to be lawmaking inspector approved.

Oor do I non need a freeze proof type hither to pass inspection? If I don't then what blazon, and size etc. would I need to buy?

To assist you visualize the area I am working in, I accept attached a pic of the area and wall that the 1/two inch PEX line volition laissez passer through to feed the hose bib. I'll look for your answer. And thanks for this great spider web site, and the ability to send you questions!

This Q&A were posted originally at PLUMBING Organisation Audit DIAGNOSE REPAIR

...

Continue reading at FAUCETS, OUTDOOR HOSE BIBBS - topic home, or select a topic from the closely-related articles beneath, or encounter the complete Article Alphabetize.

Or see these

Faucet Repair Articles

• FAUCETS & CONTROLS, KITCHEN & Bath
• FAUCETS, OUTDOOR HOSE BIBBS
• FAUCET LEAK, VALVE SEAT REPAIR
• FAUCET LEAK, VALVE Stem REPAIR
• FAUCET LEAK, WASHER REPLACEMENT
• FAUCET, SILLCOCK ANTI SIPHON LEAK REPAIR
• FREEZE-PROOF PIPES
• PLUMBING CONTROLS & VALVES - photos and descriptions of all types of plumbing valves.

Suggested commendation for this spider web folio

SILLCOCK INSTALLATION & REPAIR at InspectApedia.com - online encyclopedia of building & environmental inspection, testing, diagnosis, repair, & trouble prevention advice.

Or run across this

INDEX to RELATED ARTICLES: Article INDEX to PLUMBING VALVES

Or use the SEARCH BOX found below to Ask a Question or Search InspectApedia

...

Ask a Question or Search InspectApedia

Try the search box just below, or if you adopt, postal service a question or comment in the Comments box below and nosotros will reply promptly.

Search the InspectApedia website

Note: appearance of your Annotate below may be delayed: if your annotate contains an image, web link, or text that looks to the software as if it might be a web link, your posting will announced after it has been canonical by a moderator. Apologies for the filibuster.

Technical Reviewers & References

Click to Testify or Hibernate Citations & References

Publisher InspectApedia.com - Daniel Friedman

How To Repair Leaking Stem On Freeze Proof Outside Faucet,

Source: https://inspectapedia.com/plumbing/Woodford-Sillcock-Anti-Siphon-Valve-Repair.php

Posted by: shislergaidge.blogspot.com

Share this post